• I get no sound at the digital output. What do I do wrong?
• How many characters of MP3 files are shown?
• How quickly can the player wind?
•  Is the player macrovision-off and code-free?
• The movie runs asynchronously. Is the player defective?
• I get sound but no screen. Is the player defective?
• Will Kodak CDs be replayed?
• Will burned CDs be replayed, and if yes, what formats?
• My player doesn’t replay burned CDs. What’s the reason for this?

If you couldn't find answer to you question, please send you question to
MAS Support Team.

• I get no sound at the digital output. What do I do wrong?
  
  
Please see, if the Player has been set on digital. To do this enter the setup menu and the sub menu “Audio setup” and then enter “output”. There you can select between 2-channel (stereo), 5.1. output (analogue) and SPDIF/PCM or SPDIF/RAW (digital).
• How many characters of MP3 files are shown?
  
  
Up to 7 characters are shown.
• How quickly can the player wind?
  
  
SVCDs, VCDs, Audio CDs and DVDs can be wind by 32 times.
•  Is the player macrovision-off and code-free?
  
  

Regrettably the player is not macrovision-off, but you can set the player on code-free. To do this do as follows: Press the setup key on your remote control. The setup menu will be shown. Now press the following keys vol + / vol + / vol + / vol + on your remote control. The version number will be shown in the right upper quarter of your TV screen. VER 2 is region code 2. If you need region code 1, press once the left arrow key in the middle of your remote control. With the right arrow key you set higher region codes. To set the player on code-free, you need to press up to VER 255.

TV shows version 1: region code 1
TV shows version 2: region code 2
TV shows version 3: region code 3
TV shows version 4: region code 4
TV shows version 5: region code 5
TV shows version 6: region code 6
TV shows version 255: all region codes

After you adjusted the region codes, please press again the setup key. The player will show the programmed region code.


• The movie runs asynchronously. Is the player defective?
  
  
If this problem occurs with burned CDs, please check the bit rate and the speed you’ve used (ref. question 1). If it happens with original DVDs look for scratches or dirt on the medium. Probably it’s because of this. If this all is not the case, please contact our Support. The player might be defective.
• I get sound but no screen. Is the player defective?
  
  
Check if the player is correctly connected with your TV and recheck all the cables. If you’re not sure the cables work properly, change them. Press the PAL/NTSC key on your remote control. If you still don’t get a screen, please get in touch with our Support.
• Will Kodak CDs be replayed?
  
  
Yes, the Kodak Photo CD is recognised with and without Smart Navi. The pictures can be zoomed and set on “pause” at will. The player can only replay JPEGs, CDs with PCD photo format won’t be read.
• Will burned CDs be replayed, and if yes, what formats?
  
  
We tested formats CD-R(W), DVD-R(RW), DVD+R(W), which was replayed by the player. However, due to the multitude of writers, blanks, software and options to burn, we cannot give any guarantees, that all burned DVDs will be read.
• My player doesn’t replay burned CDs. What’s the reason for this?
  
  
Check closely how you burned or encoded the formats. It’s important that the video bit rate for VCDs is approx. 1400 and for SVCDs is 2400. Don’t burn faster than 8 times, for SVCDs we recommend the slowest speed possible, otherwise you might experience synchronisation problems.